Test principle and application of power amplifier TDA7294

Test principle and application of power amplifier TDA7294

1. Chip description TDA7294 is a novel DMOS high-power integrated circuit that was launched by the famous European SGS-THOMSON STMicroelectronics in the 1990s to mainland China. It sweeps the sound, cold and hard sounds of the linear amplifier and thick film integration in the past, and is widely used in the field of HI-FI: such as home theaters and active speakers. tda7294.pdf
The design of the chip is focused on sound, and has the advantages of bipolar signal processing circuit and power MOS. It has the characteristics of high pressure resistance, low noise, low distortion, and affinity for replaying sounds. It also has silent standby function, short circuit current and overheat protection function to make its performance more perfect.
Working voltage range: (VCC + VEE) = 80V
Output power: up to 100W
Voltage range: | VCC | + | VEE | = 20V-80V
Quiescent current: 30MA
Output power: | VCC | = | VEE | = 35V, RL = 8 ohm is 70W
Total harmonic distortion (THD): 0.01% (typical value)
Conversion rate (SR): 10V / us
Open loop gain: 80dB
The purchase price is 13 yuan per person at the author ’s location; due to limited conditions, the test circuit is soldered with a universal board, as long as the speaker is not too difficult. The sound quality is not bad; because the author ’s technology is not yet mature, to master the sound effects of this chip, please master Pointing improvements.
2. The function of each end of the pin data is as follows:
Pin 1 is the standby terminal; Pin 2 is the inverting input terminal;
Pin 3 is the positive phase input terminal; Pin 4 is grounded;
5, 11, 12 feet are empty feet; 6 feet are bootstrap ends;
Pin 7 is + Vs (signal processing part); Pin 8 is -Vs (signal processing part);
9 feet are standby feet; 10 feet are silent feet;
Pin 13 is + Vs (last stage); Pin 14 is the output terminal;
15 feet are -Vs (last level).
Test and application of power amplifier TDA7294
3. Description of circuit diagram R1, R2 and R5 form a typical power amplifier with an amplification factor of approximately 32 times that of R5 / R1;
2. C1, C2, C8, C9 are power supply filter capacitors;
3. Pin 9 and pin 10 can be added with switches to control standby and mute. C6 and C7 are used for filtering and debounce.
Test and application of power amplifier TDA7294
4. Test conditions 1. No load, use WD-5 voltage source + 12.1 -12.1 +5.0 to provide power and allowable bits
2. Use SG1732SB5A DC stabilized current supply as input.
3. Use the multimeter SYG DT9205G to measure the value.
Test and application of power amplifier TDA7294
Fifth, the test summary started the test and mistakenly believed that the linear range was low. After analysis, the amplification factor was too large, but the maximum voltage of 3.86V was still too small to be suitable for certain high-voltage output requirements; it is still good as a general audio chip (excluding fever) .

Disclaimer: This article is Liang Weiwen's original work, if you need to reprint, please contact the author

.Shell is made of high quality fire retardant PC material, up to the European environmental requirements, burning non-toxic. 
2.Inside Material is made of Tin phosphorous bronze, with good electrical conductivity, not easily deformed.
3.Built-in automatic recovery fuse,more safe.
4. Automatically adjust charging Wattage.
5.Double USB charging interface, support more USB devices to charging at the same time.
6.2100 MA output current,can reduce charging time.
7.Compatibility: iPod, iPhone, iPad, Tablets, Mobile Phones, MP3 Bluetooth Headsets, GPS & more.

USB UL

USB UL,USB UL data transfer cable,USB UL cable,Mini USB UL

Hoojet Electric Appliance Co.,Ltd , https://www.hoojetgfci.com